Vending machine dimensions vary more than most buyers expect. A full-size US snack or drink machine is about 72 inches (1,830 mm) tall, 35–39 inches (890–990 mm) wide and 29–36 inches (735–915 mm) deep. KioskForce floor-standing models are 1,970–1,975 mm tall, 616–1,310 mm wide and 735–820 mm deep. Countertop and wall-mounted machines are a different scale altogether. This guide gives sizes by type, then the checks that actually stop installations: doorways, lifts, the space in front for the user and the door, and the power outlet.
Quick answer
- Full-size (US): about 72 in (1,830 mm) high × 35–39 in (890–990 mm) wide × 29–36 in (735–915 mm) deep.
- KioskForce floor-standing: 616–1,310 mm wide × 735–820 mm deep × 1,970–1,975 mm high, depending on model.
- Narrow, countertop and wall-mount: from about 616 mm wide (KF6X10) down to wall units typically 200–350 mm deep.
- Doorways: a machine goes through on its depth, and US accessible doors need only 815 mm clear. Measure.
- In front: room for the door to swing fully open, plus a 760 × 1,220 mm clear floor space for the user in the US.
- Power: a matching outlet within cord reach, ideally on a dedicated circuit.
What is the standard vending machine size?
There is no formal standard, but full-size machines have converged on a common envelope because they share delivery routes, doorways and break-room alcoves. These are published figures from manufacturers’ own pages. Metric conversions are ours.
| Machine | Type | Height | Width | Depth |
|---|---|---|---|---|
| AMS Classic Snack | Full-size glass-front snack | 72 in (1,829 mm) | 35 or 39 in (889 or 991 mm) | 35 in (889 mm) |
| Seaga ENV5S Snack | Full-size glass-front snack, 5-wide | 72 in (1,829 mm) | 39 in (991 mm) | 36 in (914 mm) |
| Seaga Prosper | Full-size cold-drink machine | 72 in (183 cm) | 39 in (99 cm) | 34 in (86 cm) |
| Seaga QB4000 Quick Break Combo | Mid-range snack and drink | 73.5 in (1,867 mm) | 35 in (889 mm) | 34.5 in (876 mm) |
| AMS SlimGem | Narrow floor-standing | 72 in (1,829 mm) | 28.5 in (724 mm) | 29.5 in (749 mm) |
| Seaga Snak-Mart | Mid-range | 69.5 in (177 cm) | 30 in (77 cm) | 29 in (74 cm) |
| Seaga SM16 PPE | Countertop | 28.5 in (73 cm) | 30 in (77 cm) | 29 in (74 cm) |
KioskForce is not affiliated with AMS or Seaga. They are named only because they publish dimensions for a range of machine types.
So when someone asks about vending machine size, the honest short answer for a full-size machine is “about 1.8 m tall, about 1 m wide and about 0.9 m deep”, and the honest long answer is “it depends on the model; get the spec sheet”.
KioskForce vending machine dimensions
| KioskForce model | Width | Depth | Height | Notes |
|---|---|---|---|---|
| KF6X10 | 616 mm | 735 mm | 1,970 mm | Narrow 3-wide, 10-inch flush touchscreen, ambient or refrigerated |
| BG10X10 | 1,110 mm | 820 mm | 1,975 mm | 5-wide with 10-inch sidecar screen, from USD 1,200 |
| KF10X22 | 1,310 mm | 820 mm | 1,975 mm | 22-inch touchscreen, from USD 2,100 |
| K180-6C locker kiosk | 750 mm | 400 mm | about 1,830 mm | 21.5-inch screen, six cells, from USD 1,800 |
| L180-10C locker | 750 mm | 400 mm | 1,830 mm | Ten cells, sizes customisable |
| Compact wall-mount | typically 400–600 mm | typically 200–350 mm | typically 600–900 mm | Built to the pack; USD 800–1,500 |
Every machine is built to order, so these are starting points; custom enclosures change them. The dimensions of your build are on the specification issued with the quotation. For wall-mounted machines, depth, coil pitch, screen size and mounting height are covered in detail in wall-mounted vending machine dimensions; this page does not repeat them.
Width: selections and screens
Width is mostly a count of columns. A 3-wide cabinet such as the KF6X10 carries six selections per row; a 5-wide such as the BG10X10 carries ten. With six trays, that is up to 36 or 60 selections respectively.
Screens and payment hardware add width when they sit beside the product window rather than in the door. The KF10X22 is 200 mm wider than the BG10X10 at the same depth and height, and that width carries its 22-inch touchscreen and room behind it for card readers and extra sensors. Before you choose the widest machine, check that the position is wide enough for the cabinet plus a little side clearance for the door hinge and cleaning.
Depth: the dimension that decides the route
Depth sets how many items sit behind each selection: a longer coil holds more packs. It is also the dimension that decides whether the machine gets into the building, because a machine goes through a doorway on its depth.
Under the 2010 ADA Standards, a door opening needs a clear width of only 32 inches (815 mm) minimum, measured between the face of the door and the stop with the door open at 90 degrees. Many doors are wider, but the minimum is narrower than many full-size machines are deep:
| Machine depth | Through an 815 mm clear opening? |
|---|---|
| Wall-mount, 200–350 mm | Yes, easily |
| L180-10C or K180-6C, 400 mm | Yes |
| KF6X10, 735 mm | Yes, with about 80 mm to spare |
| AMS SlimGem, 749 mm | Yes, with about 65 mm to spare |
| BG10X10 or KF10X22, 820 mm | No, without a wider door or removing the door leaf |
| A 35–36 in (889–914 mm) deep full-size machine | No, without a wider opening |
This is geometry, not a statement about your building. Measure the clear opening of every door on the route, not the door leaf, and remember the door itself, its handle and its closer all eat into the clear width.
Height: door closers, trolleys and lifts
Height rarely limits the final position, but it limits the trip. The ADA Standards set 80 inches (2,030 mm) of vertical clearance in circulation areas, with an exception that lets door closers and door stops sit as low as 78 inches (1,980 mm). A 1,975 mm machine standing on the floor clears that by 5 mm. Put it on a trolley or pallet jack and it does not.
Plan with your mover how a full-height machine will pass through doorways: whether door closers need removing for the day, or what equipment the machine will travel on. Do not improvise by rocking or walking the machine; vending machines are heavy and tip-overs kill. How much do vending machines weigh? covers weights, floors and tipping.
Lifts. The ADA Standards’ table for new elevator cars sets door clear widths of 36 inches (915 mm) for a side door and 42 inches (1,065 mm) for a centred door, with a minimum of 51 inches (1,295 mm) from the back wall to the front return. Check your lift’s actual door width, internal dimensions and rated load against the machine; an older or smaller lift can be much tighter.
Space in front: the user and the door
A vending machine needs floor space in front of it for two different people: the customer and the restocker.
| Space | Figure | Source or reasoning |
|---|---|---|
| Clear floor space for the user (US) | 30 × 48 in (760 × 1,220 mm) minimum | 2010 ADA Standards, 305.3 |
| Walking route kept clear beside it (US) | 36 in (915 mm) minimum | 2010 ADA Standards, 403.5.1 |
| Reach range for controls, reader and bin (US) | 15–48 in (380–1,220 mm) above the floor, unobstructed | 2010 ADA Standards, 308.2.1 and 308.3.1 |
| Door swing for restocking | About the width of the door itself, in front of the machine | Geometry of a hinged front door |
| Space behind and beside, refrigerated builds | As stated on the spec sheet for airflow | Model-specific; ask for it |
The first three apply where the ADA Standards apply. Elsewhere, use your local access standard. We build to the height and layout you specify and do not certify compliance with any access standard on your behalf.
This is a summary for planning, not legal advice. Rules change; confirm with the regulator where the machine will stand.
A machine in a corridor has to leave the required route width beside it. A machine in an alcove has to leave room for its door. Both are easy to forget when only the cabinet’s footprint is measured.
Power: what the outlet must provide
The socket is a dimension problem too: it has to be close enough for the cord, and the circuit has to carry the machine.
- Match the supply. Seaga lists its glass-front Envision machines at 115 V, 60 Hz and 4 A. KioskForce builds each machine to the destination market’s supply, such as 110 V/60 Hz for North America or 220–240 V/50 Hz for Australia, New Zealand, Europe and most of Asia. That is specified at quotation, not adapted after delivery.
- Size the circuit for the surge. Refrigerated cabinets start a compressor, which draws hardest at start-up. A circuit shared with other loads is the usual cause of trips.
- Position the outlet within the cord length stated on the spec sheet, and where the machine can be pulled forward for service without straining it.
The full checklist is in vending machine power, voltage and market compliance. Running cost by machine type is in how much electricity a vending machine uses.
How to measure a position
Take these measurements before you ask for a quotation:
- The position itself: width, depth available and ceiling height, noting skirting boards, pipes and sockets.
- The front: clear floor space for users and the door swing, plus any walking route alongside.
- The route: clear width of every door, corridor turns, steps, and the lift’s door width, internal size and rated load.
- The supply: voltage, socket type and position, and whether the circuit is dedicated.
- The floor: level or not, and whether it is a slab, a raised floor or a mezzanine.
A phone photo of the position with a tape measure in shot is often more useful than a drawing.
What to specify if you are buying one
Send us the position measurements above with what the machine must dispense, who will use it and how they pay. We will propose a cabinet that fits the position and the route, and state its dimensions, weight and crated size on the quotation. Compare types and prices on the smart vending machines hub and vending machine cost, lay out selections with the planogram configurator, or send an enquiry.
Lead times are 4–6 weeks for a modified standard model and 8–12 weeks for a fully custom design. On-site installation is optional and, in some regions, provided through a local distributor; otherwise your own contractor positions and connects the machine.
Where a full-size machine is the wrong answer
- The route cannot take it. If an 815 mm door, a small lift or a staircase is unavoidable, choose a narrow cabinet such as the 616 mm wide, 735 mm deep KF6X10, or a wall-mount.
- The position cannot give the space in front. A corridor that would lose its walking route needs an alcove, a shallower machine or a different spot.
- The range is small and light. A wall-mounted machine or a locker cabinet does the job without taking a square metre of floor.
- Bulky or returnable items. Lockers suit them better than coils; see custom smart lockers.
Frequently asked questions
What are the standard dimensions of a vending machine?
There is no single standard, but full-size US snack and drink machines cluster around 72 inches (1,830 mm) tall, 35 to 39 inches (890 to 990 mm) wide and 29 to 36 inches (735 to 915 mm) deep, going by AMS and Seaga published specifications. KioskForce floor-standing models are 1,970 to 1,975 mm tall, 616 to 1,310 mm wide and 735 to 820 mm deep. Countertop and wall-mounted units are far smaller. Always work from the spec sheet of the exact model.
Will a vending machine fit through a standard door?
Check it, because it is often close. A machine goes through a doorway on its depth, and a full-size machine is roughly 735 to 915 mm deep. The 2010 ADA Standards require only 32 inches (815 mm) of clear width at a door opening, measured between the face of the open door and the stop, so an 820 mm deep machine can fail to pass a minimum-width door. Measure the clear opening, not the door leaf, along every door on the route.
How much space do you need in front of a vending machine?
Enough for the user and for the door. In the US, the ADA Standards call for a clear floor space of at least 30 by 48 inches (760 by 1,220 mm) where a person uses an element, and a walking route of 36 inches (915 mm) should stay clear beside it. For restocking, the cabinet door must be able to swing fully open, which on a hinged door means roughly the door’s own width in front of the machine.
What is the smallest vending machine size?
Countertop and wall-mounted machines are the smallest. Seaga lists its SM16 PPE countertop unit at 28.5 inches high, 30 wide and 29 deep. KioskForce compact wall-mount units are typically 400 to 600 mm wide, 200 to 350 mm deep and 600 to 900 mm high, built to the pack they dispense. Among floor-standing machines, the KioskForce KF6X10 is 616 mm wide and AMS lists its SlimGem at 28.5 inches (724 mm).
How tall is a vending machine?
Most full-size machines are about 72 inches (1,830 mm) tall in the US market; Seaga’s QB4000 is listed at 73.5 inches. KioskForce full-size models are 1,970 to 1,975 mm, and the K180-6C locker kiosk about 1,830 mm. Height matters on the delivery route: the ADA Standards allow door closers and stops as low as 78 inches (1,980 mm), so a 1,975 mm machine has almost no room to spare upright on a trolley.
What power outlet does a vending machine need?
One that matches the machine’s rated supply, within reach of its cord, preferably on a dedicated circuit. Seaga lists its glass-front Envision machines at 115 V, 60 Hz and 4 A. KioskForce builds each machine to the destination market’s supply, for example 110 V 60 Hz for North America or 220 to 240 V 50 Hz for Australia and Europe, and states the rated draw on the spec sheet. Refrigerated machines draw more and have a start-up surge.
How deep is a wall-mounted vending machine?
KioskForce compact wall-mount units are typically 200 to 350 mm deep, 400 to 600 mm wide and 600 to 900 mm high, against 735 to 820 mm deep for our floor-standing models. The shallow depth is the point of the format, but it also limits how many packs sit behind each selection. Our wall-mounted vending machine dimensions guide covers depth, coil pitch, capacity and mounting height in detail.
References
- U.S. Access Board — “ADA Accessibility Standards” (2010 ADA Standards for Accessible Design: 305.3, 307.4, 308, 403.5.1, 404.2.3, Table 407.4.1; accessed 3 October 2026). https://www.access-board.gov/ada/
- AMS (Automated Merchandising Systems) — “Classic Snack” and “SlimGem”, specifications (accessed 3 October 2026). https://amsvendors.com/classic-snack/ and https://amsvendors.com/slimgem
- Seaga Manufacturing — “ENV5S Snack”, specifications (accessed 3 October 2026). https://seaga.com/products/glass-front-vendors/env5s-snack/
- Seaga Manufacturing — “The Prosper”, specifications (accessed 3 October 2026). https://seaga.com/products/cold-beverage-vendors/the-prosper/
- Seaga Manufacturing — “Quick Break Combo QB4000”, “Snak-Mart” and “SM16 PPE”, specifications (accessed 3 October 2026). https://seaga.com/products/mid-range-vending/quick-break-combo-qb4000/, https://seaga.com/products/mid-range-vending/snak-mart/ and https://seaga.com/products/mid-range-vending/sm16-ppe/
Related
- Smart vending machines: types, pricing and how to buy: the hub for this cluster
- How much do vending machines weigh?
- How much electricity does a vending machine use?
- Touch screen vending machines for sale
- Wall-mounted vending machine dimensions and capacity
- Wall-mounted vs floor-standing vending machines
Talk to us about sizing a machine
Send the position’s measurements, the narrowest door and lift on the route, and the power supply. We will propose a cabinet that fits and state its dimensions, weight and crated size on the quotation.
Project brief · 60 seconds
What are we building together?
Three quick steps. Your brief goes straight to the engineers who design, build and support KioskForce systems.
